• For a printed version of our brochure, click on the PDF below.
    PDF (621kb 10/18/2004)  
• To view the DC53 v D2  Test Report page, 
  click here.  
• To view results of two machinability tests on DC53 vs D2, click below. 
  - Machinability Test Report #1
  - Machinability Test Report #2
• To see what our customers say about DC53, 
  click here.   

High-performance coating helps stamper fight downtime   Dies last longer, need no regrinding.   READ MORE

New CrN Tool Coatings READ MORE

Is It Tough Enough for You? Can a new tool steel that machines like butter really be tough enough to withstand the pounding?   READ MORE

UNIQUE CHARACTERISTICS Higher hardness (62-64 HRc) than D2 after heat treatment. Twice the toughness of D2 with superior wear resistance. Substantially higher fatigue strength compared to D2. Smaller primary carbides than D2 protect the  die from chipping and cracking. Secondary refining process (DLF) reduces impurities. Machines and grinds up to 40% faster than D2. Less residual stress after wire EDMing.

RETURN TO TOP

APPLICATIONS

• Stepped punch and press-punching dies
• Concrete sprayer parts, rotor plates
• Swaging dies and backers
• Dies for cold forging
• Thread-rolling circular dies
• Piercing punch
• Thread-rolling dies for heat-treated bolts
• Forming dies
• Stripper plates for lead frame blanking
• Gauges
• Screws for injection molding machines
• Plastic Molds

RETURN TO TOP

BENEFITS

Welding
Lower minimum pre- and post-heating temperature than D2 reduces the incidence of weld
cracking and simplifies welding. Low hardness decline in heat affected zone minimizes
deterioration in die performance.

Weld Rod - any appropriate weld rod used for high carbon, high chrome die steels such as D-2.

Machining/Grinding
Machines and grinds better and faster than D2 for longer tool life and reduced tool manufacturing
time.

EDM
Residual stress caused by quenching is minimal in DC53. Therefore, problems such as cracking
and distortion are prevented during and after wire electro-discharge machining.

Sub-surface hardness decline of DC53 just below wire electro-discharge machining is much
less than D2; thus making DC53 dies more durable.

Stability
High-temperature tempering (520°C) allows maintenance of die accuracy without the
troublesome application of subzero treatment, reducing costs and increasing productivity.

Surface Enhancements
Surface hardening treatments such as CVD, PVD, TD, and nitriding require the use of high
temperatures. DC53’s higher inner hardness than D2 after such treatments, preventing the
hardened layer from peeling off and making surface hardening treatments more effective.





Wear
Superior wear-resistance coupled with high toughness make DC53 suitable for use in
wear-resistant parts subject to impact and bending stress.

Strength
Dies made of DC53 and heat-treated using standard method possesses up to 25% higher
bending strength than D2. Secondary refining decreases nonmetallic inclusions and carbide
size for a substantially increased fatigue strength that of D2.

Toughness
Superior impact value minimizes fracture and chipping problems thus ensuring
more durable dies.

RETURN TO TOP

PHYSICAL PROPERTIES

Coefficient of Thermal Expansion (x10-6/C°)

Coefficient of Thermal Conductivity (cal/cm·sec°C)

RETURN TO TOP

GENERAL DESIGN GUIDELINES

Strength
DC53 high hardness (HRc62) coupled with standard methods of heat treating result in
superior bending strength, up to 25% higher than D2. Ideal for dies to form high tensile
steel plates and other heavy-thickness steel plates and cold forming tools undergoing
high loads such as dies for bending and cold forging.

A secondary refining process minimizes the size of carbides and decreases nonmetallic
inclusions for a substantially increased fatigue strength over D2. This characteristic makes DC53
suitable for use where repeated stresses are loaded, such as precision-punching dies with
small clearance and cold forming tools. DC53 is particularly suited to handling
less-workable materials such as stainless and heat-treated alloy steels.

Stability
Dimensional changes of dies in operation are caused mainly by decomposition of retained
austenite. High-temperature tempering (520° to 530°C) reduces the presence of austenite
to 5% or less, providing the same effect as the troublesome application of subzero treatment.
This reduction in retained austenite makes DC53 particularly suitable for precision dies and
gauges where dimensional changes during operation must be minimized.

Hardness
DC53 can be hardened to 62-64 HRc in the same manner as D2, and when tempered at high
temperatures (520° to 530°C), it assumes excellent properties. Even when tempered at lower
temperatures (180° to 200°C), its performance is equivalent to or better than that of D2. This
improved hardenability makes heat treatment easier and reduces hardness problems due to
vacuum heat treatment, which uses gas cooling.

Smaller primary carbides give DC53 twice the toughness of D2

RETURN TO TOP

WEAR PROPERTIES

DC53 displays superior wear-resistance to D2 when tempered at high temperatures (520°C) and equal wear resistance to D2 when tempered at low temperatures. High resistance to temper softening minimizes seizing and galling on the die surface. DC53 is ideal for dies needing to maintain high surface hardness against frictional heat between the die surface and the worked materials.

RETURN TO TOP

PROCESSING GUIDELINES

Machining and Grinding
DC53 contains perfectly spheroidized primary carbides. Therefore, it is superior in machinability and grindability to D2. Its grindability, in particular, is 30 to 40% better than that of D2 and facilitates grinding of thin tools and accurate sizing of die detail. In addition, since DC53 is tempered at high temperatures, there is little possibility of grinding cracks and the number of processes required for die manufacture can be reduced.

Presentation:  Machinability Test: To evaluate the machinability of DC53 vs. D2.  (This is a 750k PDF and requires Acrobat Reader to view.)

Hardness decline due to grinding heat is also prevented, thus raising die performance.

EDM
In order to perform highly accurate wire electro-discharge machining, it is recommended
that high-temperature tempering (520°C or higher) be conducted twice to minimize heat
treatment residual stress. Reduction of residual stress is insufficient if applying subzero
treatment and repeated tempering at low temperatures. In order to avoid deceleration of
machining speed, rust formation, and galvanic corrosion, the following procedures are
recommended.

1. Make the machining fluid spray pressure as high as possible and place the upper and
   lower nozzles close to the material to be worked in order to smoothly wash away the
   sludge formed on the machined surface. This is especially necessary for machining
   heavy-walled materials.
2. Maintain specific resistance of machining fluid at an appropriate value. If the specific
   resistance falls (electric conductivity of machining fluid rises), galvanic corrosion and
   deterioration of the layer tend to occur due to the influence of electrolization.
3. In addition to the above, consider use of a rust-preventive agent to prevent rust and
   adoption of the immersion process (which prevents the machined surface from coming
   into contact with the air and oxidizing).

HEAT TREATING
Standard heat treatment conditions are shown in the diagrams and tables below. As shown in the CCT curve graph, DC53 is superior in hardness to D2 and can be quenched sufficiently by air or gas cooling in a vacuum furnace. DC53 and D2 require the same austenitizing temperatures (1,020 – 1,040°C) and can be heat-treated at the same time. High temperature tempering (520°C or higher) allows DC53 to retain its high hardness and wire electro-discharge machinability. Even when tempered at low temperatures (180-200°C), DC53 remains twice as tough and equal or higher in hardness (wear resistance) than D2.

Dimensional changes due to heat treatment.

Recommendations on Heat Treatment
  
Heating procedure in quenching and tempering is basically identical for both DC53 and D2.
However, the conditions outlined below are recommended according to use and purpose.

Heat Treatment Temperature According to Use and Purpose

Dimensional Changes due to Heat Treatment of a Shaped Block

RETURN TO TOP

DIE APPLICATIONS

Blanking dies for electric home appliance components

Application:
Blanking dies for Ni based alloy materials used for medium-scale production of television
components.

Results

Considerations

Conventional Steel–The worked material is tough and chipping and seizing of the die edge were problematic. DC53–Both high temperature tempering and high hardness are important in preventing seizing and extending the life of the die edges. High hardness, when tempered at high temperature, and homogeneous structure of DC53 were greatly effective in meeting these requirements.

FB punches for electric appliance components

Application
FB punches for hook-shaped electric appliance components. Long, thin shape promotes
severe conditions.

Results

Considerations

Conventional Steel–Cracking and fracturing at the tip of the long, thin shape, shortened life. DC53–Because of DC53’s excellent toughness, hardness could be increased, resulting in more than double the life.

Plastic molds for electric appliance components

Application
Injection molds for electromagnetic switch boxes. Since the material worked is FRP resin, wear
in the area surrounding the gate is particularly problematic.

Results

Considerations

Conventional Steel–The mold was discarded due to wear occurring in areas surrounding the gate and where the flow of resin became irregular. DC53–Applying the highest hardness of DC53 (HRc63) proved highly effective in combating simple wear.

Cold forging punches for electric instrument components

Application
Working of bushings by backward extrusion.

Results

Considerations

Conventional Steel–Wear of punch edge and galling lateral face shortened durability. DC53–To prevent wear and galling, hardness of DC53 was tempered at a high level, resulting in expected extension of life (due to its high toughness, this material resists cracking.)

Flat thread rolling dies

Application
Flat thread rolling dies for working stainless steel bolts where there is a particularly high working
load.

Results

Considerations

Conventional Steel–Chipping and local seizing of threads, required early regrinding. DC53–In working with stainless steels, high toughness, high hardness, and high resistance to temper softening are necessary. DC53 proved effective.

Rolls for straightening machines

Application
Straightening of heat-resistant steel and stainless steel where pitting of the roll is a major
problem and high hardness and toughness are required.

Results

Considerations

Conventional Steel–Pitting of roll surface and local seizing occurred, terminating life. DC53–The basic characteristics of DC53 fully met the requirements for high toughness to prevent pitting and high hardness to prevent seizing.

Trimming dies for bolt (hexagonal)

Application
This type of die is commonly used. Surface hardness treatment is applied depending on the
material worked and the precision of the finish required.

Results